SECAM has been supporting you for over 50 years in the design and industrialisation of inserts for plastics, light alloys and wood, with more than 300 references available from stock.
Simple and quick manual assembly
Very sharp teeth to allow better penetration into the material
Long with two anchor crowns
Low cost
Anchorage increasing torque and pull-out resistance
- Low cost
- Simple and quick manual assembly
- Anchorage increasing torque and pull-out resistance
- Long with two anchor crowns
- Very sharp teeth to allow better penetration into the material
Técnica de fijación – Grandes series – E-Shop
Div 5
Div 3
Div 6
Div 4
Div 1
Div 2
Image technique 1
Image technique 2
| Part Number | Thread M (6H) | L (mm) | Ø E (mm) | Ø A (mm) | Ø B (mm) | Well Ø | Technical sheet | 3D |
|---|---|---|---|---|---|---|---|---|
| IE L 030 080 T056 L 0 | M3 X 0.50 | 8 | 5.6 | 5 | 4.5 | 4.60 - 4.70 |  | |
| IE L 030 095 T056 L 0 | M3 X 0.50 | 9.5 | 5.6 | 5 | 4.5 | 4.60 - 4.70 | | |
| IE L 040 080 T066 L 0 | M4 X 0.70 | 8 | 6.6 | 6 | 5.4 | 5.50 - 5.60 | | |
| IE L 040 095 T066 L 0 | M4 x 0.70 | 9.5 | 6.6 | 6 | 5.4 | 5.50 - 5.60 | | |
| IE L 050 090 T076 L 0 | M5 X 0.80 | 9 | 7.6 | 7 | 6.5 | 6.60 - 6.70 | | |
| IE L 060 090 T086 L 0 | M6 x 1.00 | 9 | 8.6 | 8 | 7.5 | 7.60 - 7.70 | | |
| IE L 080 100 T106 L 0 | M8 X 1.25 | 10 | 10.6 | 10 | 9.4 | 9.50 - 9.60 | |
Phase
01
The insert is placed in a cavity which is either drilled or moulded in: the well.
Phase
02
The insert is forced into the well by axial pressure, deforming slightly in the process. The insert will be flush with the material to avoid possible removal due to lever effect.
Phase
03
As the screw goes in, the insert returns to its original shape, the locking pyramids are forced into the material, providing holding force and torque resistance. Select a screw long enough to effectively force the locking pyramids into the material. The screw must never come into contact with the bottom of the well.
- According to laboratory tests carried out on unfilled materials
- Values given for information only
Product |
Sub-family |
Type |
Thread |
L |
Outer Shape |
Ø E |
Materials |
Specification |
|||||||
Example |
I |
E |
L |
0 |
2 |
0 |
0 |
8 |
0 |
T |
0 |
3 |
9 |
L |
0 |
|
Insert |
Expansion |
Long with 2 locking rings |
Internal thread |
Total length 8 mm |
Knurled |
Largest diameter 3.9mm (1/10mm) |
Brass CW 614N |
None |
|||||||
| Sub-families U Ultrasonic V Screw S Moulded-in E Expansion P Pressed-in |
Expansion insert type Outer shape |
Materials |
Specifications 0 none 1 ZnNi Zinc Nickel N Nickelage |
