Post-molding installation
High tear resistance
Self tapping
3 cutting holes
Thin Wall
- Post-molding installation
- High tear resistance
- Self tapping
- 3 cutting holes
- Thin Wall
Técnica de fijación – Grandes series – E-Shop
Div 5
Div 3
Div 6
Div 4
Div 1
Div 2
Image technique 1
Image technique 2
| Part Number | Thread M (6H) | L (mm) | Ø E | Well Ø plastics | Well Ø light alloys | Technical sheet | 3D |
|---|---|---|---|---|---|---|---|
| IV 8 035 050 M050 A 0 | M3.5 X 0.60 | 5 | 5 X 0.60 | 4.6 à 4.7 | 4.7 à 4.8 |  | |
| IV 8 040 060 M060 A 0 | M4 x 0.70 | 6 | 6 x 0.70 | 5.4 à 5.6 | 5.6 à 5.7 | | |
| IV 8 050 070 M065 A 0 | M5 X 0.80 | 7 | 6.5 X 0.80 | 6.0 à 6.1 | 6.1 à 6.2 | | |
| IV 8 060 080 M080 A 0 | M6 x 1.00 | 8 | 8 x 1.00 | 7.4 à 7.6 | 7.6 à 7.7 | | |
| IV 8 080 090 M100 A 0 | M8 X 1.25 | 9 | 10 X 1.25 | 9.3 à 9.5 | 9.5 à 9.6 | | |
| IV 8 100 100 M120 A 0 | M10 x 1.50 | 10 | 12 x 1.50 | 11.1 à 11.3 | 11.3 à 11.5 | | |
| IV 8 120 120 M140 A 0 | M12 X 0.75 | 12 | 14 X 1.75 | 13.1 à 13.3 | 13.3 à 13.5 | | |
| IV 8 140 140 M160 A 0 | M14 x 2.00 | 14 | 16 x 2.00 | 15.0 à 15.2 | 15.2 à 15.4 | | |
| IV 8 160 140 M180 A 0 | M16 X 2.00 | 14 | 18X 2.00 | 17.0 à 17.2 | - | |
Phase
01
The tool positions the insert along its axis in the moulded well or drilling hole. self-drilling: the material is forced back without making chips self-tapping: the cutting slot cuts the material.
Phase
02
The locknut or the tool mechanism separates the tool and the insert. The material compresses the insert, holding it securely.
Chip tray
Lb Well depth:
To recover the chips produced during installation
Insert length +2 à 3 mm
Open Well
The insert must be fully buried in the material:
Insert length +1 mm
Commodily plastics
60° chamber
Pc = 1 to 1.5 x ext. thread pitch
Technical plastics
& High-performances plastics & Light allows
ØL =Ø ext + 0.2 to 0.4 mm
PL =1 à 1.5 x ext. thread pitch
Pc =1 à 1.5 x ext. thread pitch
Torque & speed for tempered steel
type 2 screw insert
ØP / Well diameter
A larger hole will make it easier to fit the insert but at the expense of the holding force and torque resistance.
Plan a counterbore and/or a chamber to fit the insert more easily an ensure that it is flush with the surface of the material.
S / Wall thickness
Depends on the material elasticity and the stress on the assembly
Commodity plastics:
S ≥ 0.25 to 0.9 insert outer Ø
Technical & high performance plastics & light alloys:
S ≥ 0.2 to 0.6 insert outer Ø
| Internal thread | M2.5 M3 | M4 M5 | M6 M8 | M10 M12 | M14 M16 |
| Speed of rotation in r.p.m. | from 800 to 1300 | from 600 to 900 | from 400 to 700 | from 300 to 450 | from 240 to 350 |
Tests strongly recommended: our laboratory is at your disposal
Advantages
- Ensures optimal assembly
- Speed of installation
- Possibility of mounting the tool on a screwdriver or on a hand tool
- Long version available if hole is difficult to access
Manual
Automatic
Training square
Counter nut
| Reference | Ø | B | D | C |
|---|---|---|---|---|
| OVM 025 CM 0050 A 0 | M2.5 | 55 | 5 | 7 |
| OVM 030 CM 0050 A 0 | M3 | 55 | 5 | 7 |
| OVM 035 CM 0050 A 0 | M3.5 | 60 | 5 | 7 |
| OVM 040 CM 0050 A 0 | M4 | 60 | 5 | 7 |
| OVM 050 CM 0050 A 0 | M5 | 75 | 8 | 13 |
| OVM 060 CM 0050 A 0 | M6 | 75 | 8 | 13 |
| OVM 080 CM 0050 A 0 | M8 | 75 | 8 | 13 |
| OVM 100 CM 0050 A 0 | M10 | 95 | 12.5 | 19 |
| OVM 120 CM 0050 A 0 | M12 | 95 | 12.5 | 19 |
01
Fit a left-hand turn on the driving part of the tool. Mount the insert onto the tool with the slot or cutting holes facing down.
02
Engage the insert with light pressure at the start of installation to correctly form the first threads.
03
At the end of assembly, the insert must penetrate 0.1 to 0.2 mm ± 1/4 turn) below the surface of the part.
04
Using a wrench, lock the lock nut and unscrew the turn to the left to separate the insert from the tool. The stud of the tool is placed in the middle of the cutting slot so as not to block the clearance cutting chips.
| Reference | Ø | C | A | D | B |
|---|---|---|---|---|---|
| OVA 025 CM 0063 A 0 | M2.5 | 18 | 8 | 6.3 | 78 |
| OVA 030 CM 0063 A 0 | M3 | 18 | 8 | 6.3 | 78 |
| OVA 035 CM 0063 A 0 | M3.5 | 18 | 8 | 6.3 | 78 |
| OVA 040 CM 0063 A 0 | M4 | 18 | 8 | 6.3 | 78 |
| OVA 050 CM 0063 A 0 | M5 | 24 | 12.5 | 10 | 95 |
| OVA 060 CM 0063 A 0 | M6 | 24 | 12.5 | 10 | 95 |
| OVA 080 CM 0063 A 0 | M8 | 24 | 12.5 | 10 | 95 |
| OVA 100 CM 0063 A 0 | M10 | 32 | 16 | 12.5 | 118 |
| OVA 120 CM 0063 A 0 | M12 | 32 | 16 | 12.5 | 118 |
01
Adjust the depth stop so that the contact face of the tool penetrates 0.1 to 0.2 mm below the surface of the part.
02
Place the insert on the well.
Slot or sharp hole downwards.
Engage with light pressure.
Screw without pressure.
03
At the end of assembly, the insert must penetrate 0.1 to 0.2 mm ± 1/4 turn) below the surface of the part.
Product |
Sub-family |
Type |
Thread |
L |
Outer Shape |
Ø E |
Materials |
Specification |
|||||||
Example |
I |
V |
8 |
0 |
4 |
0 |
0 |
5 |
0 |
M |
0 |
5 |
0 |
A |
0 |
|
Insert |
Screw |
flat bottom net – with 3 cutting holes, thin walls |
Internal thread |
Total length 5 mm |
Metric pitch |
External diameter 5 mm |
Hardened steel |
None |
|||||||
| Sub Families S Mouled-in V Screw E Expansion P Pressed-in U Ultrasonic |
Screw insert Type K with head and thread 45° to bottom 160° – reversible + internal hexagon H without head and 45° thread at 160° bottom – reversible + internal hexagon 1 non-split – 60° ext. thread, ISO metric pitch 2 with cutting slot – 60° ext. thread, fine pitch 7 flat-bottom thread, 3 cutting holes 8 flat bottom net – with 3 cutting holes, thin walls 9 with cutting slot for soft platics and wood |
Materials |
Specifications 0 None N Nickel plating ZnNi Zinc Nickel |
