Post-molding installation
High tear resistance
Self tapping
Cutting slot
- Designed for screwing into hard plastics
- Caution: generation of a cutting chip
- Good mechanical strength
- Self-tapping insert thanks to its cutting slot
Técnica de fijación – Grandes series – E-Shop
Div 5
Div 3
Div 6
Div 4
Div 1
Div 2
Image technique 1
Image technique 2
| Part Number | Thread M (6H) | L (mm) | Ø E | Well Ø | Technical sheet | 3D |
|---|---|---|---|---|---|---|
| IV 2 020 060 M045 L0 | M2 X 0.40 | 6 | 4.5 X 0.50 | 4.1 - 4.2 |  | |
| IV 2 025 060 M045 L0 | M2.5 x 0.45 | 6 | 4.5 x 0.50 | 4.1 - 4.2 | | |
| IV 2 030 060 M050 L0 | M3 X 0.50 | 6 | 5 X 0.50 | 4.6 - 4.7 | | |
| IV 2 035 080 M060 L0 | M3.5 x 0.60 | 8 | 6 x 0.75 | 5.5 - 5.6 | | |
| IV 2 040 080 M065 L0 | M4 X 0.70 | 8 | 6.5 X 0.75 | 6.0 - 6.1 | | |
| IV 2 050 100 M080 L0 | M5 x 0.80 | 10 | 8 x 1.00 | 7.3 - 7.5 | | |
| IV 2 060 120 M090 L0 | M6 X 1.00 | 12 | 9 X 1.00 | 8.3 à 8.5 | | |
| IV 2 060 140 M100 L0 | M6 x 1.00 | 14 | 10 x 1.50 | 8.9 à 9.2 | | |
| IV 2 080 150 M120 L0 | M8 X 1.25 | 15 | 12 X 1.50 | 10.9 à 11.2 | | |
| IV 2 100 180 M140 L0 | M10 x 1.50 | 18 | 14 x 1.50 | 12.9 à 13.2 | | |
| IV 2 120 220 M160 L0 | M12 X 1.75 | 22 | 16 X 1.50 | 14.9 à 15.2 | | |
| IV 2 140 240 M180 L0 | M14 x 2.00 | 24 | 18 x 1.50 | 16.9 à 17.2 | | |
| IV 2 160 220 M200 L0 | M16 X 2.00 | 22 | 20 X 1.50 | 18.9 à 19.2 | |
Phase
01
The tool positions the insert along its axis in the moulded well or drilling hole. self-drilling: the material is forced back without making chips self-tapping: the cutting slot cuts the material.
Phase
02
The locknut or the tool mechanism separates the tool and the insert. The material compresses the insert, holding it securely.
Chip tray
Lb Well depth:
To recover the chips produced during installation
Insert length +2 à 3 mm
Open Well
The insert must be fully buried in the material:
Insert length +1 mm
Commodily plastics
60° chamber
Pc = 1 to 1.5 x ext. thread pitch
Technical plastics
& High-performances plastics & Light allows
ØL =Ø ext + 0.2 to 0.4 mm
PL =1 à 1.5 x ext. thread pitch
Pc =1 à 1.5 x ext. thread pitch
Torque & speed for tempered steel
type 2 screw insert
ØP / Well diameter
A larger hole will make it easier to fit the insert but at the expense of the holding force and torque resistance.
Plan a counterbore and/or a chamber to fit the insert more easily an ensure that it is flush with the surface of the material.
S / Wall thickness
Depends on the material elasticity and the stress on the assembly
Commodity plastics:
S ≥ 0.25 to 0.9 insert outer Ø
Technical & high performance plastics & light alloys:
S ≥ 0.2 to 0.6 insert outer Ø
| Internal thread | M2.5 M3 | M4 M5 | M6 M8 | M10 M12 | M14 M16 |
| Speed of rotation in r.p.m. | from 800 to 1300 | from 600 to 900 | from 400 to 700 | from 300 to 450 | from 240 to 350 |
Tests strongly recommended: our laboratory is at your disposal
INSTALLATION TOOLS
MANUAL INSTALLATION TOOLS – OVM
01
Fit a tap wrench
on the square end of the tool.
Fit the insert on the tool, with the slot or cutting holes downwards
02
Engage the insert, pressing gently as you start to cut the first threads correctly.
03
hen correctly fitted, the insert must lie 0.1 to 0.2 mm.
(± 1/4 turn) below the part surface.
04
Use a spanner to tighten the locknut and unscrew the tap wrench to separate the insert from the tool.
The tool stud is positioned in the middle of the cutting slot to avoid blocking the chips.
- Scroll horizontally across the table
| Reference | Ø insert interior | Dim. of the square in mm | D2 Shaft diameter in mm |
|---|---|---|---|
| OVM 025 CM 0050 A 0 | M2,5 | 5 | 6 |
| OVM 030 CM 0050 A 0 | M3 | 5 | 6 |
| OVM 040 CM 0050 A 0 | M4 | 5 | 6 |
| OVM 050 CM 0080 A 0 | M5 | 8 | 10 |
| OVM 060 CM 0080 A 0 | M6 | 8 | 10 |
| OVM 080 CM 0080 A 0 | M8 | 8 | 10 |
| OVM 100 CM 0127 A 0 | M10 | 12,5 | 16 |
| OVM 120 CM 0127 A 0 | M12 | 12,5 | 16 |
AUTOMATIC RELEASE TOOL – OVA
01
Set the depth gauge so that the tool bearing face penetrates 0.1 to 0.2 mm below the part surface.
02
Fit the insert on the tool, with the slot or cutting holes downwards.
Engage the insert, pressing gently. Screw in without applying pressure.
03
Reverse the drill at end of installation. The pin separates from the insert tool by mechanical effect (impact).
- Scroll horizontally across the table
| Cylindrical Shank + Drive Square | with 1/4″ (6.35 mm) hexagonal shank | |||
|---|---|---|---|---|
| Reference | Ø insert interior | Dim. of the square in mm | D2 Shaft diameter in mm | Reference |
| OVA 020 CM 0063 A 0 | M2 | 6,35 | 8 | OVA 020 HM 01/4 A 0 |
| OVA 025 CM 0063 A 0 | M2,5 | 6,35 | 8 | OVA 025 HM 01/4 A 0 |
| OVA 030 CM 0063 A 0 | M3 | 6,35 | 8 | OVA 030 HM 01/4 A 0 |
| OVA 035 CM 0063 A 0 | M3,5 | 6,35 | 8 | OVA 035 HM 01/4 A 0 |
| OVA 040 CM 0063 A 0 | M4 | 6,35 | 8 | OVA 040 HM 01/4 A 0 |
| OVA 050 CM 0100 A 0 | M5 | 9,53 | 12,5 | OVA 050 HM 01/4 A 0 |
| OVA 060 CM 0100 A 0 | M6 | 9,53 | 12,5 | OVA 060 HM 01/4 A 0 |
| OVA 080 CM 0100 A 0 | M8 | 9,53 | 12,5 | OVA 080 HM 01/4 A 0 |
| OVA 100 CM 0127 A 0 | M10 | 12,70 | 16 | OVA 100 HM 01/4 A 0 |
| OVA 120 CM 0127 A 0 | M12 | 12,70 | 16 | – |
OVK – Queue hexagonale 1/4’’ ( 6,35 mm)
- Faites défiler horizontalement le tableau
| Complete Tool | Components Retail tools | ||
|---|---|---|---|
| Référence | Ø intérieur insert | Door reference End cap | Reference End piece |
| OVK 030 HM 01/4 A 0 | M3 | PORTE-OVCOM | EMBOUT-OVCOM3 |
| OVK 040 HM 01/4 A 0 | M4 | PORTE-OVCOM | EMBOUT-OVCOM4 |
| OVK 050 HM 01/4 A0 | M5 | PORTE-OVCOM | EMBOUT-OVCOM5 |
| OVK 060 HM 01/4 A 0 | M6 | PORTE-OVCOM | EMBOUT-OVCOM6 |
| OVK 080 HM 01/4 A 0 | M8 | PORTE-OVCOM | EMBOUT-OVCOM8 |
Common spring blade: REF Blade-Spring-OVCOM
For installing IVK inserts
OVH – 1/4″ (6.35 mm) hexagonal shank
with automatic disengagement
- Faites défiler horizontalement le tableau
| Outil Complet | Composants Outils pour achat au détail | ||
|---|---|---|---|
| Référence | Ø intérieur insert | Référence Embout | |
| OVH 030 HM 01/4 A 0 | M3 | – | EMBOUT-OVCOM3 |
| OVH 040 HM 01/4 A 0 | M4 | – | EMBOUT-OVCOM4 |
| OVH 050 HM 01/4 A0 | M5 | – | EMBOUT-OVCOM5 |
| OVH 060 HM 01/4 A 0 | M6 | – | EMBOUT-OVCOM6 |
| OVH 080 HM 01/4 A 0 | M8 | – | EMBOUT-OVCOM8 |
Common spring blade: REF Blade-Spring-OVCOM
For installing IVH inserts
Product |
Sub-family |
Type |
Thread |
L |
Outer Shape |
Ø E |
Materials |
Specification |
|||||||
Example |
I |
V |
2 |
0 |
3 |
0 |
0 |
6 |
0 |
M |
0 |
5 |
0 |
L |
0 |
|
Insert |
Screw |
with cutting slot – external thread. 60°, with fine pitch |
Internal thread |
Total length 6 mm |
Metric pitch |
External diameter 5 mm |
Brass CW 614N |
None |
|||||||
| Sub Families S Mouled-in V Screw E Expansion P Pressed-in U Ultrasonic |
Screw insert Type K with head and thread 45° to bottom 160° – reversible + internal hexagon H without head and 45° thread at 160° bottom – reversible + internal hexagon 1 non-split – 60° ext. thread, ISO metric pitch 2 with cutting slot – 60° ext. thread, fine pitch 7 flat-bottom thread, 3 cutting holes 9 with cutting slot for soft platics and wood |
Materials |
Spécifications 0 None N Nickel plating ZnNi Zinc Nickel |
